Now, there are many people who test the c1 driver's license, but they get automatic licenses after they get the driver's license. When they get on the train, they are forced to fight. How is it different from manual transmission? Why can't I get fire? I believe many newcomers have encountered such problems. Today, we will take a look together. Is it necessary to step on the brake pedal before starting the automatic car? Actually, there are two design modes for automatic vehicles. One is that the brakes must be applied before they can be started. The other is that they can be started without pressing the brakes, depending on the actual model. In general, most automatic vehicles do not need to step on the brakes when they start. Unless they are hung in the N position and they do not pull the handbrake, they must take some brakes for safety reasons. The automatic transmission is generally set to start the engine only when it is in the N position or in the p position, and it is not necessary to step on the brake. However, when it is engaged in R or D, you should step on the brakes. Although the car does not have to be stepped on, the engine power will be output to the wheels after the R or D gear is engaged. The car will move. For safety, Should brake on the brakes. First, the automatic opening of the automatic car First of all, don't push hard when you can't move the gear lever. 99% of it is probably what you did wrong. For example, if the button in the thumb position on the lever is pressed, press it to pull it out of the P position or push it into the P position. It is important to note that this organ is designed to prevent misoperations, and it is extremely dangerous to push the R or P gear in the course of driving! 1. When parking, you must hang the P file and pull the parking brake. Parking here refers to parking for a longer period of time and people may leave the vehicle. 2. The engine can be ignited only in P and N gears. Moreover, because of the first point, when the vehicle is restarted after parking, it must be in the P position. No other gear can be hung before the general engine fires. Correct ignition action: 1. Turn the key to 1 (or 2) squares; many lights on the instrument panel are on, and the computer in the car starts self-check (equivalent to the start of the PC). At the same time, the oil pump starts to work. After a few seconds, the lights went out. According to the different cars, some lights will be extinguished after ignition. 2, step on the brake, ignition. 3, and other engine idle speed down to normal speed, water temperature indicator after the start of the move, step on the brakes, hanging D file, loose hand brake. 4, loose brakes, go. 5, step on the accelerator to accelerate, step on the brake deceleration. 6, meet the red light or other reasons need to stop for a short time, step on the brake to keep the car still. Loosen brakes. Second, the advanced method of automatic transmission First of all, many automatic files are often accelerated with delays. When you step on the throttle, the engine speed rises quickly, but the acceleration is not fast, which is generally between half a second and one second. Then, the acceleration quickly rose and it seemed that the stamina was sufficient. With this flexibility, you can avoid braking in the urban area just after acceleration, or when everything is overtaking at high speeds, it is only in the dilemma of poor acceleration. 1. Don't use the N file when it's okay, only when: 1 Turn off the engine during the drive, and quickly advance the neutral gear to re-ignite. Afterwards, advance the D-range to the repair shop. 2 How the engine can't beat, and when other vehicles need to use a tow rope or a hard connection to pull it. Hanging N file. Don't slip away from a car like a manual car, unless you think that saving money is safer than that! ! ! And the life of the transmission is important. 2. When you are driving, if you loosen the throttle, the transmission often thinks that you want to enter the economy (or fuel economy) mode. At this time, if possible, the transmission will automatically raise one gear. However, the transmission will never reach the fifth gear as fast as the taxi driver. So, if possible, pay attention to when the general transmission shifts up. Such as POLO, when normal, if the speed is slightly greater than 20,40,60 when loose the throttle, it will upshift. In urban roads, the flexible use of throttle upshifts will reduce fuel consumption. 3. When overtaking on a freeway, one of the techniques of manual gearing is to lower one gear. The automatic file can also achieve this function, but it is not so straightforward. 1 Accelerate first, or make sure your car's speed is about the same or slightly faster. Change course if needed. 2 Lightly press the throttle, loose the throttle. 3 Repeat the previous action. 4 Squeeze the throttle, notice, slam the throttle. You will experience the buzz and pushback of the engine. Cool! My experience is that if the original speed is too slow, either this function will not be used or if it is downshifted, it will be too effortless. It is advisable to practice on the road with no cars at all times, so as to prevent the movements from being deformed when the time comes, the throttle is stepped on and the stalls are not lowered. Nowadays, a good automatic transmission has a memory and learning function. It takes a long time to open. Your habits will be accepted by it and reflected in the shifting action. 4, can not always use the D file 1 When you are on a long, steep ramp, if you are hanging in D, you may feel that the transmission is busy shifting, it will rise, and it will drop. At this time, it hurt the transmission. It should be stopped by the brakes, hang 1, 2 or 3 and then start. The specific link to the file depends on your specific situation. For example, the slope of an ordinary hand-cartrailer 2 can go up, and the automatic transmission has been busy, so it should be correct to put it in the 2nd gear. 2 In the long, steep slopes, if you are hanging in D, you may need to use the brakes to control the speed; if you use the brakes for a long time, the brakes may be inefficient due to overheating, which is dangerous; and, many mountain roads Without asphalting, Shi Zilu slams on the brakes even more dangerous, even with ABS. Stop the brakes by the side, hang 1, 2 or 3 stops and start. The same as above, with reference to the manual gear position, it is decided to use several gears. Note that you should never push the gear from D to 1, 2 or 3 while driving. If your transmission is in a high-end position and you force it to a low-end position, oh, I don't need to say that the sound of killing chickens will make you feel bad and depressed for a while. If the transmission is damaged, it can belong to the repair, the cost of 4 to 5 that! The above is about some techniques of the automatic car opening method. As for the automatic car start, do not step on the brakes. Xiao Bian thinks that although the brakes can not be started, but for safety reasons, or with a little brake is better, if the road is uneven, not It's easy to cause a slip after starting the brakes.
In
order to deliver the Sheet Metal Parts intact it is essential to package the
product properly and make Sheet Metal Parts Packed well. Thus the reason to careful packaging is not primarily aesthetic
but we carry out in order to preserve the condition of our products. Packaging
processes and Foam Packing material, if customer does not provide separate
packaging plan, is determined by the mode of transportation. We attach a
bar code to the Sheet Metal parts packed according to the needs of our
customers for the easy identification. We also make customized packaging by
customized boxes.
General packaging methods used at
QL Sheet Metal:
Dispatched by post using sleeves,
packets, standard corrugated boxes
Packing in corrugated boxes, with
5 layered, glued and stitched design boxes, using spacers
Pallet, fixed with straps, using
slip-resistant interim plates, edge protectors, straps
Pallet with standard stretch foil
Paper packaging used for surface
protection and separation purposes
VCI corrosion protection and
desiccant packaging
Sheet Metal Products Packaging Sheet Metal Products Packaging,Sheet Metal Parts Packed,Foam Packing,Box Packaging QL Sheet Metals Co.,Ltd , http://www.ql-metals.com